MY BOOK : PRACTICAL MICROSTRIP AND PRINTED ANTENNA DESIGN

Practical Microstrip and Printed Antenna Design
Practical Microstrip and Printed Antenna Design Book Cover
My new book: “Practical Microstrip and Printed Antenna Design”, is all set to be released by end of this month (March 2019). The book covers the topic of microstrip antennas from roughly three vantage points: printed antenna fundamentals, antenna design technique, and design of real-world application-based antennas. This comprehensive resource presents antenna fundamentals balanced with the practical design of printed antennas. Microstrip and printed antennas are used in radars, aerospace systems, internet of things (IoT), satellite systems, 5G networks, MIMO, automobiles, and mobile phones. Supported with essential equations and illustrations, this practical book helps evaluate various design aspect of the antenna. Based on several years of my research in antenna design and development for RF and microwave applications, this book offers in-depth coverage of microstrip and printed antenna design methodology for modern applications. This book not only contains the crucial elements required to know to design printed antennas but also helps with the following:
  • Many practical designed antenna projects covered in book, which can be used for practice and real-world projects
  • Latest antenna technologies covering 5G, automobiles, GPS, RFID, Radar, Phased array and many other applications
  • Incorporates the various antenna design techniques used by industries and academia

Comments

Post a Comment

Popular posts from this blog

Image
Slotted Waveguide Array Antenna Slotted antenna arrays used with waveguides are a popular antenna in navigation, radar, and other high-frequency systems. A waveguide is a very low loss transmission line. It allows propagating signals to a number of smaller antennas (slots). Each of these slots allows a little of the energy to radiate. Slot impedance and resonant behavior for a single slot are dependent on slot placement and size. Its exceptional directivity in the elevation plane gives it quite high power gain. The slotted waveguide has achieved most of its success when used in an omnidirectional role To make the unidirectional antenna radiate over the entire 360 degrees of azimuth, the second set of slots are cut on the back face of the waveguide. An 8×8 planar four pole X-band Tchebyshev dual inductive post substrate integrated waveguide filter from 10.15 GHz to 10.7 GHz is designed for terrestrial broadcasting. The filter is designed on the 5870 with a relative dielectric...
Read more

EMI & EMC Compliance of Smartphone

EMC within electronic components has become an increasingly important issue for embedded designers to contend with. As system frequencies and the need for lower supply voltages increase, the end application becomes more and more vulnerable to the negative affects of EMI. These electrical influences can be generated by either radiated or conductive EMI sources. Radiated sources include anything electrical or electromechanical, including motors, power lines, antennas, traces on a PCB (Printed Circuit Board), and even the silicon components on the PCB. Conductive EMI primarily shows itself as electrical “noise” on the power supply lines of an application and can be caused by induced voltage spikes from other devices within a system. Electromagnetic Interference (EMI): Electromagnetic emissions from a device or system that  interfere with the normal operation of another device or system. EMI is also referred to as Radio Frequency Interference (RFI) Electromagnetic Compatibilit...
Read more

QFN Package Simulation

Image
he Quad Flat No-lead (QFN) package is a CSP (plastic encapsulated package) with a copper lead frame substrate. QFN type package is one of the most cutting-edge IC packaging technologies in the electronics. The QFN is a leadless package where electrical contact to the PCB is made by soldering the leads on the bottom surface of the package to the PCB, instead of the conventional formed perimeter gull wing leads. The QFN-type package is known for its small size, cost-effectiveness and good production yields. QFN also possess certain mechanical advantages for high-speed circuits including improved co-planarity and heat dissipation. The QFN has pins on 4 edges of the bottom surface of the package. The QFN can have either a square or rectangle body as well as symmetric or asymmetric terminal patterns. The QFN was introduced to replace the gull wing lead Quad Flat Package (QFP) because the component leads are embedded in the plastic and cannot be bent during handling to insure consistent ...
Read more